Joey's Notes: The Red Hat Linux Boot Process
By Joey Prestia
Understanding the Linux boot process is crucial for being able to effectively troubleshoot a Linux system, when boot problems occur. For example, someone could have made some undocumented changes during the previous shift to a critical file that affects the boot process. Now, it's your shift, and you have to bring the machine down for a hardware upgrade. Upon boot up, the system crashes, and you're stuck there until you solve the issue. Learning the steps involved in the boot process, and knowing what happens at each phase, will help you quickly diagnose any problems that come up.
Many current Linux distributions mask the boot process from the user by
using a boot splash screen that can usually be bypassed by pressing the
<ESC> key or some key sequence when the splash screen is being
displayed, and may require removing "
quiet" (on Red Hat-based distributions) from the kernel line in
/boot/grub/grub.conf. Because there are so many different Linux
distributions, you will need to check the documentation for your distro for
the splashscreen bypass procedure, if you need one.
This cannot be stressed enough: you need to get familiar with the boot process before problems arise. There are some key files involved with the boot process; e.g., an error in /boot/grub/grub.conf, /etc/fstab or /etc/inittab, and you're sure to have problems. So, in addition to knowing the boot process, it's a good idea to really learn these files.
Caution: if you do anything with /boot/grub/grub.conf, or any critical configuration file, do it only on a machine that's a practice computer (sandbox), until you fully understand the process. I use Virtualbox virtualization software, to practice recovering from various self-inflicted boot problems.
[ When working with critical files - and doubly so when you're not sure what you're doing - making backups will save you again and again. At the very least, you should make a copy, or preferably a series of copies of the file before changing it (e.g., "grub.conf.3.orig" for "grub.conf"); there are times when critical errors can go unnoticed for a while. -- Ben ]
Power-On Self Test
The first thing to occur in the boot process is the Power-On Self Test (POST) that is performed by the compter's Basic Input/Output System (BIOS), when it is powered on. This self test is just that -- an internal check of the system's internal components. Other architectures may use different ways to accomplish this, but the purpose is identical. This checking normally involves the system RAM, CPUs, video card, hard drives, and other motherboard components. Many other types of internal cards such as RAID cards and various other types of controller cards perform their own self-testing. If errors occur, some form of alert will be generated or sent to a panel or console; the POST uses a series of beeps to indicate the specific error encountered. If all goes well, the BIOS reads the master boot record on the hard disk and loads the program that is found there into memory.
Master Boot Record
The Master Boot Record (MBR) is the first 512 bytes of the boot drive that is read into memory by the BIOS. (This is assuming we are using an x86 architecture.) The first 446 bytes of that 512 will normally contain a low-level boot code that points to a boot loader somewhere else on the disk - it can even point to another hard disk. The next 64 bytes contain the partition table for the disk (four 16-byte entries known as the IBM Partition Table Scheme). Finally, the remaining 2 bytes are the "Magic Number" (used for error detection).
The purpose of a bootloader is to load the operating system. Many boot loaders are available; however, LILO and GRUB are the most common for Linux. Windows has its own, called the New Technology Loader (NTLDR). You may have at one time or another seen the message "NTLDR is missing"; this is a Windows bootloader error.
Regardless of the bootloader being used, it is important to keep in mind that bootloaders are very complex and easily rendered inoperative by inexperienced users with root access. In my opinion, the best practice is to explore their workings only on machines you are using as sandboxes or in virtual machines to sharpen your skills. One slight typographical error while working with, e.g., grub.conf, and you may be spending more time than you anticipated trying to fix your error; however, this too, can be a great learning experience, as long as it is on a sandbox and you can afford the time.
The most common bootloader program in use today for modern Linux systems is the GRand Unified Bootloader (GRUB). This is the bootloader we will be talking about, here. The GRUB bootloader is a program written to the master boot record and /boot partition of a hard drive that loads the operating system. The bootloader code used to fit in the first 446 bytes of the MBR, but, owing to progressively increasing complexity of operating systems and the need to boot almost any operating system, it has grown in size. Currently, a subset of the bootloader code is written to the MBRi, and the remainder is written to the /boot partition. In addition, the GRUB bootloader is modular in design and works in stages which I will only cover briefly.
The stages of GRUB
GRUB works in stages called Stage1, Stage1_5, and Stage 2. I will give a brief overview of what each stage does.
The stage1 code of GRUB is written within the 512 bytes of the master boot record. Because of the limited size of the master boot record area, GRUB stage1 will usually point to the next stage of GRUB, stage1_5 or stage2. GRUB may or may not need to load stage1_5 depending on the types of filesystems present.
[root@localhost grub]# file stage1 stage1: x86 boot sector, code offset 0x48
Stage1_5 is the intermediate stage between stage1 and stage2. If you look at your /boot/grub area, you should see various stage1_5 files with names of various types of filesystems. Stage1_5 deals with specific types of filesystems, and is named after them. This code will allow the filesystem to be interpreted appropriately.
These are the stage1_5 files located in my /boot/grub directory:
e2fs_stage1_5 fat_stage1_5 ffs_stage1_5 iso9660_stage1_5 jfs_stage1_5 minix_stage1_5 reiserfs_stage1_5 ufs2_stage1_5 vstafs_stage1_5 xfs_stage1_5
This is the main GRUB image, and will usually reside on the filesystem in the /boot partition at /boot/grub/stage2. It reads the /boot/grub/grub.conf file for configuration information that details how it will load the kernel. It also has an interactive interface that will allow you to troubleshoot, re-install, or modify how GRUB works. Stage2 will present the user with a graphical boot menu entry. If the appropriate key is not pressed in the time allotted to enter the hidden menu, or nothing is selected in the time frame allowed, GRUB will boot the default entry.
GRUB has a really helpful tab-completion feature that you can use to assist you in getting your system up and running if, for example, you have a non-bootable system due to a improperly specified line in your grub.conf file. I have used it in this way many times to get unbootable systems working again.
This file specifies the kernel to load and the initrd image file with all of the modules to load for your system.
Here is a typical grub.conf file for Red Hat Linux:
# grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/hdb9 # initrd /initrd-version.img #boot=/dev/hdb default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Red Hat Enterprise Linux Server (2.6.18-53.el5) root (hd0,0) kernel /vmlinuz-2.6.18-53.el5 ro root=LABEL=/ rhgb quiet initrd /initrd-2.6.18-53.el5.img
This file is fairly easy to edit; because of this, it is a common location for errors.
GNU GRUB version 0.97 (640K lower / 3072K upper memory) [Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else, TAB lists the possible completions of a device/filename.] grub>
Nothing but a GRUB prompt - now what do we do? If you're making any changes to this file, remember to print it out first, and make a backup copy; it may save you if you make a typo. You can use the hardcopy to recall the options necessary to boot your machine and fix your mistake. There are various errors, and it pays to become familiar with some of the common ones such as an incorrectly specified kernel name, or a root partition that is improperly designated in this file. If you do see this GRUB prompt, ask yourself this question, "What do I do now to recover my system?" If you have no idea at this point, and you are managing Linux systems, it would probably be a good idea to get on a practice box and create some errors within the grub.conf, and get to know your bootloader. Here's what could be done in the above situation - notice where I hit the <TAB> key to view my options.
Booting manually with GRUB tab completion
grub> root (hd0,0) Filesystem type is ext2fs, partition type 0x83 grub> kernel /<TAB> Possible files are: lost+found grub initrd-2.6.18-8.el5.img System.map-2.6.18- 8.el5 config-2.6.18-8.el5 symvers-2.6.18-8.el5.gz vmlinuz-2.6.18-8.el5 grub> kernel /vmlinuz-2.6.18-8.el5 ro root=LABEL=/ [Linux-bzImage, setup=0x1e00, size=0x1ad054] grub> initrd /<TAB> Possible files are: lost+found grub initrd-2.6.18-8.el5.img System.map-2.6.18- 8.el5 config-2.6.18-8.el5 symvers-2.6.18-8.el5.gz vmlinuz-2.6.18-8.el5 grub> initrd /initrd-2.6.18-8.el5.img [Linux-initrd @ 0xfe8a000, 0x15547c bytes] grub> boot
root (hd0,0)" specifies the first drive, and the
first partition on that drive. On the kernel line, you can type '/', hit
<TAB>, and view your options; after selecting one, type one or more
letters (whatever's necessary for a unique name) and let GRUB complete it
for you. The additional option of "
came from my experience of working with Red Hat systems; yours may be
different - so you need to examine the options in your grub.conf file. The
same thing happens on the initrd line: after the /, hit <TAB> and let
GRUB do the work by listing your possible choices. You may also have to
further specify modules and additional options.
When GRUB transfers control to the kernel and the kernel is booting, you
may see a lot of text output. On Red Hat-based systems, the line in
grub.conf specifying the kernel may have an "
quiet" appended to it that prevents this. It stands for "Red
Hat graphical boot quiet" and will suppress kernel boot messages. When I
need to see boot messages, I interrupt the GRUB cycle by hitting the escape
key, hitting 'e' for edit (the procedure to modify the grub kernel
arguments is at the bottom of the GRUB screen), and editing the kernel
line. Removing the "
rhgb quiet" allows me to see the
kernel messages so I can determine if any of them are relevant to, e.g., a
kernel panic or a similar problem.
What is actually going on at this time is that the kernel is probing your hardware and configuring itself for your hardware. The kernel is also loading modules in the initrd image that it needs to operate your hardware. Note that the information will scroll very quickly up your screen - so, if you believe your problem exists at the kernel level, be sure to watch closely, as this is sure to give you a clue about where your problem lies. Once the kernel is done with its initialization, it starts the system's first process, which is /sbin/init.
[ Much, but not all, of the boot information is available in the /var/log/dmesg file, once you've booted. -- Ben ]
Init is the first process running on your system. It reads the /etc/inittab file, executes /etc/rc.d/rc.sysinit, then boots into the runlevel as defined in /etc/inittab.
Init starts out with a Process ID (PID) of 1. In the image above, there's a line saying "INIT: version 2.86 booting"; this is /sbin/init taking over at this point in the boot process. On the line right after that one, you see the messages being displayed by the /etc/rc.d/rc.sysinit shell script; as a matter of fact, the entire screen contains messages from that script, so you can get an idea of some of the functions it performs. Init will also normally start several instances of /sbin/getty or /sbin/mingetty, which are your virtual terminals. This is why you can hit <Ctrl> + <Alt> + < F1> through <F6> and come up with a virtual terminal.
Next, we will look at the /etc/inittab file, specifically, at the configuration file for Init:
# # inittab This file describes how the INIT process should set up # the system in a certain run-level. # # Author: Miquel van Smoorenburg, # Modified for RHS Linux by Marc Ewing and Donnie Barnes # # Default runlevel. The runlevels used by RHS are: # 0 - halt (Do NOT set initdefault to this) # 1 - Single user mode # 2 - Multiuser, without NFS (The same as 3, if you do not have networking) # 3 - Full multiuser mode # 4 - unused # 5 - X11 # 6 - reboot (Do NOT set initdefault to this) # id:5:initdefault: # System initialization. si::sysinit:/etc/rc.d/rc.sysinit l0:0:wait:/etc/rc.d/rc 0 l1:1:wait:/etc/rc.d/rc 1 l2:2:wait:/etc/rc.d/rc 2 l3:3:wait:/etc/rc.d/rc 3 l4:4:wait:/etc/rc.d/rc 4 l5:5:wait:/etc/rc.d/rc 5 l6:6:wait:/etc/rc.d/rc 6 # Trap CTRL-alt-DELETE ca::ctrlaltdel:/sbin/shutdown -t3 -r now # When our UPS tells us power has failed, assume we have a few minutes # of power left. Schedule a shutdown for 2 minutes from now. # This does, of course, assume you have powerd installed and your # UPS connected and working correctly. pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting Down" # If power was restored before the shutdown kicked in, cancel it. pr:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown Cancelled" # Run gettys in standard runlevels 1:2345:respawn:/sbin/mingetty tty1 2:2345:respawn:/sbin/mingetty tty2 3:2345:respawn:/sbin/mingetty tty3 4:2345:respawn:/sbin/mingetty tty4 5:2345:respawn:/sbin/mingetty tty5 6:2345:respawn:/sbin/mingetty tty6 # Run xdm in runlevel 5 x:5:respawn:/etc/X11/prefdm -nodaemon
Depending on what Init is doing, you may see typical Init script
verification messages getting printed to the screen, i.e., [ OK ] or
[Failed] to aid in troubleshooting. You may see a message like "Press
'I' to enter interactive startup" (on Red Hat-based systems);
this is an indication of rc.sysinit executing, and allows the operator a certain level
of control over the still-booting system. rc.sysinit ends
with your default runlevel (as defined in /etc/inittab) being
started. This is another common place for errors, because servers will
usually have the "
id:5:initdefault:" line set
to 3, so the machine boots to runlevel 3 instead of runlevel 5.
Another common place for errors is the line pertaining to
ca::ctrlaltdel:/sbin/shutdown -t3 -r now"
commented out to prevent the 3-finger salute (<Ctrl> + <Alt>
+ <Del>) from restarting the server. People are human and make
mistakes; I have seen typographical errors in both places that can
cause problems. Unlike the "
command, which will alert you if errors exist in your mount points in
the /etc/fstab file, executing the command "
will reread your /etc/inittab, but will not check for errors in
the runlevels themselves; the best way to know if errors exist is to learn
this file and to be very, very careful if you decide to modify any of the
When you enter your runlevel, you will see further Init messages being
printed to the screen (depending if your machine is configured to do so),
again ending with a [ OK ] or [Failed] depending on whether it started
successfully or not. These are your startup services within your runlevels.
When you look at your /etc/inittab file, you will see a line like
id:5:initdefault:"; this is your default runlevel.
The default runlevel on most servers will be set to 3; on desktops, of
course, it's set to 5, so we can have an X Window System session start
as soon as the system boots up.
To get an overview of what processes get started or stopped for any
particular runlevel, we should look within the /etc/rcX.d (where
X is your runlevel) directory. Inside these directories, you will
see symbolic links to the files in your /etc/init.d/ directory. The file
names will be prefixed with either a 'K' or an 'S' (signifying kill or
start) for the given daemon at that runlevel. The number immediately after
the letter positions the script in the start order, because the processes are
started alphabetically. With Red Hat-based systems, the
chkconfig" command will alter the symbolic links to
start or stop the daemon in a desired runlevel; the 'S' or 'K' will change
appropriately and the number will most likely change as well.
That sums up the outline of the boot process for a typical Linux machine. At this point, you should have a better understanding of what goes on up until the login prompt or dialog on your screen. Last of all, always pay close attention to the details: the machine will most likely tell you what is wrong if you're experiencing problems.
Joey was born in Phoenix and started programming at the age fourteen on a Timex Sinclair 1000. He was driven by hopes he might be able to do something with this early model computer. He soon became proficient in the BASIC and Assembly programming languages. Joey became a programmer in 1990 and added COBOL, Fortran, and Pascal to his repertoire of programming languages. Since then has become obsessed with just about every aspect of computer science. He became enlightened and discovered RedHat Linux in 2002 when someone gave him RedHat version six. This started off a new passion centered around Linux. Currently Joey is completing his degree in Linux Networking and working on campus for the college's RedHat Academy in Arizona. He is also on the staff of the Linux Gazette as the Mirror Coordinator.